Obtaining multilayer coatings by the detonation spraying method
https://doi.org/10.32523/ejpfm.2021050208
Abstract
This work were studied the effect of technological parameters of detonation spraying on the phase composition and tribological characteristics on the bases of NiCr and Al2O3 coatings. As well as therewas obtained and investigated multilayer coating on the basesof NiCr/NiCr-Al2O3/Al2O3. It was determined that during detonation spraying the phase composition of Al2O3 coatings strongly depends on the degree of filling the borehole with a gas mixture. The . -Al2O3 -phase content in the coatings increases when the degree of filling is 63% and 54%. Only one CrNi3 phase is observed on the diffractograms and only increase of reflex intensity (020) at barrel filling by 58% is observed by sputtering on the bases of NiCr coatings in different degrees of barrel filling. The results of the coating nanohardness study showed that the hardness of the Al2O3 coating increases depending on the content of . -Al2O3 in it. Al2O3 coating has the maximum nanohardness values and is 16.42 GPa at the borehole is filled to 63%. The nanohardness of NiCr coating has the maximum values at barrel fillingby58% and consisting of 8.02 GPa.
About the Authors
D. N. Kakimzhanov
S. Amanzholov East Kazakhstan State University
Kazakhstan
Kazakhstan
B. K. Rakhadilov
S. Amanzholov East Kazakhstan State University
Kazakhstan
Kazakhstan
D. B. Buitkenov
S. Amanzholov East Kazakhstan State University
Kazakhstan
Kazakhstan
L. G. Zhurerova
S. Amanzholov East Kazakhstan State University
Kazakhstan
Kazakhstan
M. K. Rakhadilov
LLP PlasmaScience
Kazakhstan
Kazakhstan
D. K. Yeskermessov
LLP PlasmaScience
Kazakhstan
Kazakhstan
References
1. V.Y. Ulianitsky et al., Advanced powder Technolog 29 (2018) 1859-1864.
2. N. Shaopeng et al ., Surface and Coatings Technology 307(A) (2016) 963-970.
3. M.M. Student et al., Materials Science 54 (2018) 22-29.
4. V. Matikainen et al., J. Therm. Spray Technol. 26 (2017) 1239-1256.
5. A.D. Pogrebnjak et al., Physics-Uspekhi 48(5) (2005) 487-514.
6. M. Kilic et al., Coatings 10(11) (2020) 1107.
7. B.K. Rakhadilov et al., Key Engineering Materials (2019) 301-306.
8. B.K. Rakhadilov et al., Eurasian Journal of Physics and Functional Materials 4(2) (2020) 160-166.
9. M. Maulet et al., Eurasian Journal of Physics and Functional Materials 4(3) (2020) 249-254.
10. V.Yu. Ulianitsky et al., Ceramics International 46 (2020) 27903-27908.
11. A.D. Pogrebnjak et al., Ibid. 52(1) (2009) 29-54.
12. M. Roy et al., Surf. Eng. 15 (1999) 129-136.
13. Ji-yu Du et al., Surface and Coatings Technology 369 (2019) 16-30.
14. B. Dastan et al., Key Engineering Materials 839 (2020) 137-143.
15. B. Rakhadilov et al., Coatings 11(2) (2021) 1-14 218.
Review
For citations:
Kakimzhanov D.N., Rakhadilov B.K., Buitkenov D.B., Zhurerova L.G., Rakhadilov M.K., Yeskermessov D.K. Obtaining multilayer coatings by the detonation spraying method. Eurasian Journal of Physics and Functional Materials. 2021;5(2):148-154. https://doi.org/10.32523/ejpfm.2021050208
Views: 427
Email this article 