Reserach of the mechanic-tribological characteristics of Ti3SiC2/TiC coatings after annealing
Abstract
This article investigates the influence of thermal annealing on microhardness and wear resistance of the surface of steel U9/Y9 protected by a composite coating Ti 3 SiC 2 /TiC obtained by detonation sputtering. Thermal annealing was performed in the range of temperatures 700-900 ◦ C during 1 hour. Following annealing the formation of TiO 2 and an increase in the phase content of Ti 3 SiC 2 are observed. Higher microhardness was obtained in coatings subjected to annealing at 800 ◦ C, which can be explained by an increase in the content of carbonized titanium. As the annealing temperature rises further, the thickness of the oxide layer increases, leading to a decrease in the microhardness for the coatings annealed at 900 ◦ C. According to the results of tribological tests, formation of the oxide increases wear resistance of Ti 3 SiC 2 /TiC composite surface coatings.
About the Authors
D. B. BuitkenovKazakhstan
B. K. Rakhadilov
Kazakhstan
Zh. B. Sagdoldina
Kazakhstan
D. .. Erbolatuly
Kazakhstan
S. .. Amanzholov
Kazakhstan
References
1. Z.M. Sun et al., Acta Materialia 53 (2005) 4359-4366.
2. M.W. Barsoum et al., Unique New Carbide and Nitride Materials, American Scientist 89 (2001) 334-343.
3. N.I. Medvedeva et al., Zhurnal strukturnoi khimii 4(52) (2011) 806-822.
4. M. Barsoum, Progress in Solid State Chemistry 28 (2000) 201-281.
5. V.Yu. Ulianitsky et al., Spray Technol 20 (2011) 791-801.
6. V.Yu.Ulianitsky et al., Journal of Thermal Spray Technology 20 (2011) 791-801.
7. V.E. Oliker et al., Surface and Coatings Technology 200 (2006) 3573-3581.
8. C. Senderowski et al., Intermetallics 18 (2010) 1405-1409.
9. D.V. Dudina et al., Ceramics International 40 (2014) 3253-3260.
10. B.K. Rahadilov et al., Tribologia 1 (2019) 49-55.
11. M. Skakov et al., Bulletin of KazNTU 3(103) (2014) 65-71.
12. Y. Zhou, Z. Metallkd 1(95) (2004) 50-56.
13. M.W. Barsoum: Prog. Solid St. Chem. 28(1-4) (2000) 201-281.
14. M.W. Barsoum et al., Interceram. 49(4) (2000) 226.
15. Z.F. Zhang et al., J. of Alloys and Compounds (2003) 352:283.
16. Siddhartha et al., Materials and Design 32 (2011) 615-627.
17. B.K. Rakhadilov et al., Materials testing 4(61) (2019) 304-308
18. M.A. Caravaca et al., Journal of the European Ceramic Society 34 (2014) 3791-3800.
19. D.B. Buitkenov et al., Key Engineering Materials 821 (2019) 301-306.
20. B.K. Rakhadilov et al., International Trends in Science and Technology (2019) 28-32.
Review
For citations:
Buitkenov D.B., Rakhadilov B.K., Sagdoldina Z.B., Erbolatuly D..., Amanzholov S... Reserach of the mechanic-tribological characteristics of Ti3SiC2/TiC coatings after annealing. Eurasian Journal of Physics and Functional Materials. 2020;4(1):86-92. https://doi.org/10.29317/ejpfm.2020040109